* Sea-Bird SBE 9 Data File:
* FileName = C:\cruise\current\oc1603c-ctd2.hex
* Software Version Seasave V 7.23.2
* Temperature SN = 2329
* Conductivity SN = 1568
* Number of Bytes Per Scan = 41
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Mar 21 2016 13:31:39
* NMEA Latitude = 44 37.39 N
* NMEA Longitude = 124 02.04 W
* NMEA UTC (Time) = Mar 21 2016  20:31:47
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.2
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
** Ship:R/V Oceanus oc1603c
** Station: YB-1
** Operator:
** Latitude:
** Longitude:
** Depth (uncorrected)
** Time:
* System UTC = Mar 21 2016 20:31:39
# nquan = 19
# nvalues = 4                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = timeS: Time, Elapsed [seconds]
# name 3 = t090C: Temperature [ITS-90, deg C]
# name 4 = c0S/m: Conductivity [S/m]
# name 5 = sal00: Salinity, Practical [PSU]
# name 6 = depSM: Depth [salt water, m]
# name 7 = prDM: Pressure, Digiquartz [db]
# name 8 = t190C: Temperature, 2 [ITS-90, deg C]
# name 9 = c1S/m: Conductivity, 2 [S/m]
# name 10 = sal11: Salinity, Practical, 2 [PSU]
# name 11 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 12 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 13 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 14 = altM: Altimeter [m]
# name 15 = par: PAR/Irradiance, Biospherical/Licor
# name 16 = pumps: Pump Status
# name 17 = nbin: number of scans per bin
# name 18 = flag: flag
# span 0 =   44.62314,   44.62316       
# span 1 = -124.03412, -124.03407       
# span 2 =     32.875,    176.081       
# span 3 =    11.9686,    11.9748       
# span 4 =   3.301771,   3.409441       
# span 5 =    28.3054,    29.3269       
# span 6 =      0.876,      2.647       
# span 7 =      0.884,      2.668       
# span 8 =    11.9683,    11.9741       
# span 9 =   3.314593,   3.409327       
# span 10 =    28.4258,    29.3261      
# span 11 =     1.6790,     1.8566      
# span 12 =    252.000,    278.211      
# span 13 =     5.7646,     6.3676      
# span 14 =       7.26,       9.48      
# span 15 = 7.8053e+01, 2.6772e+02      
# span 16 =          1,          1      
# span 17 =         19,       1579      
# span 18 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = Mar 21 2016 20:31:48 [NMEA time, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2329</SerialNumber>
#       <CalibrationDate>10-Dec-15</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.33999084e-003</G>
#       <H>6.41368492e-004</H>
#       <I>2.31947431e-005</I>
#       <J>2.23782705e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1568</SerialNumber>
#       <CalibrationDate>10-Dec-15</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.00836187e+000</G>
#         <H>5.19753114e-001</H>
#         <I>-2.69417543e-004</I>
#         <J>3.73199160e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>0256</SerialNumber>
#       <CalibrationDate>18-Dec-15</CalibrationDate>
#       <C1>-4.705724e+004</C1>
#       <C2>-4.431410e-002</C2>
#       <C3>8.991870e-003</C3>
#       <D1>4.427900e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.014264e+001</T1>
#       <T2>-2.990150e-004</T2>
#       <T3>3.699150e-006</T3>
#       <T4>5.702540e-009</T4>
#       <Slope>0.99988503</Slope>
#       <Offset>-2.13730</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.140000e-002</AD590M>
#       <AD590B>-8.242000e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2633</SerialNumber>
#       <CalibrationDate>10-Dec-15</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.36642256e-003</G>
#       <H>6.47846316e-004</H>
#       <I>2.37885699e-005</I>
#       <J>2.27435940e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1553</SerialNumber>
#       <CalibrationDate>10-Dec-15</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.18147406e+000</G>
#         <H>5.25599649e-001</H>
#         <I>3.52361041e-006</I>
#         <J>2.78827283e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Free -->
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLRTD-426</SerialNumber>
#       <CalibrationDate>12 FEB 2015</CalibrationDate>
#       <ScaleFactor>2.30000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0250</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Transmissometer, WET Labs C-Star -->
#     <WET_LabsCStar SensorID="71" >
#       <SerialNumber>CST-1031DR</SerialNumber>
#       <CalibrationDate>2 Feb 2015</CalibrationDate>
#       <M>21.4290</M>
#       <B>-0.0858</B>
#       <PathLength>0.250</PathLength>
#     </WET_LabsCStar>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>1232</SerialNumber>
#       <CalibrationDate>12-Dec-15</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.3216e-001</Soc>
#         <offset>-0.5024</offset>
#         <A>-3.9714e-003</A>
#         <B> 1.5061e-004</B>
#         <C>-2.5888e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.3800</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Free -->
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1022</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>14.850</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>70135</SerialNumber>
#       <CalibrationDate>11 Jan 2016</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>18348620000.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.05733192</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 09 2018 20:59:35, 7.23.2 [datcnv_vars = 17]
# datcnv_in = Z:\data\r2r\cruise\OC1603C\fileset\124090\data\oc1603c-ctd2.hex Z:\data\r2r\cruise\OC1603C\fileset\124090\data\oc1603c-ctd2.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Jan 09 2018 20:59:40, 7.23.2
# celltm_in = Z:\data\local\cruise\OC1603C\products\r2rctd\oc1603c-ctd2.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Jan 09 2018 20:59:43, 7.23.2
# binavg_in = Z:\data\local\cruise\OC1603C\products\r2rctd\oc1603c-ctd2.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
   44.62316 -124.03407     32.875    11.9748   3.301771    28.3054      0.876      0.884    11.9741   3.314593    28.4258     1.6790    252.000     5.7646       9.48 2.6772e+02          1       1579 0.0000e+00
   44.62314 -124.03410     69.375    11.9731   3.404830    29.2797      1.989      2.005    11.9725   3.404920    29.2810     1.8566    277.871     6.3598       8.30 1.3572e+02          1        169 0.0000e+00
   44.62314 -124.03410     76.436    11.9686   3.409441    29.3269      2.647      2.668    11.9683   3.409327    29.3261     1.8453    277.928     6.3613       7.52 8.9082e+01          1        164 0.0000e+00
   44.62314 -124.03412    176.081    11.9704   3.405581    29.2887      2.456      2.476    11.9703   3.405781    29.2907     1.7884    278.211     6.3676       7.26 7.8053e+01          1         19 0.0000e+00