* Sea-Bird SBE 9 Data File:
* FileName = C:\data\ctd\at3601x.hex
* Software Version Seasave V 7.23.2
* Temperature SN = 4303
* Conductivity SN = 3009
* Number of Bytes Per Scan = 40
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Jul 31 2016 15:32:25
* NMEA Latitude = 39 48.67 N
* NMEA Longitude = 069 35.39 W
* NMEA UTC (Time) = Jul 31 2016  15:32:30
* Store Lat/Lon Data = Append to Every Scan
* System UTC = Jul 31 2016 15:32:25
# nquan = 19
# nvalues = 2                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = t090C: Temperature [ITS-90, deg C]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = sal00: Salinity, Practical [PSU]
# name 5 = depSM: Depth [salt water, m]
# name 6 = prDM: Pressure, Digiquartz [db]
# name 7 = t190C: Temperature, 2 [ITS-90, deg C]
# name 8 = c1S/m: Conductivity, 2 [S/m]
# name 9 = sal11: Salinity, Practical, 2 [PSU]
# name 10 = par: PAR/Irradiance, Biospherical/Licor
# name 11 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 12 = altM: Altimeter [m]
# name 13 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 14 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 15 = spar: SPAR/Surface Irradiance
# name 16 = pumps: Pump Status
# name 17 = nbin: number of scans per bin
# name 18 = flag: flag
# span 0 =   39.81118,   39.81118       
# span 1 =  -69.58984,  -69.58984       
# span 2 =    24.5790,    24.6086       
# span 3 =   5.173763,   5.177421       
# span 4 =    34.3287,    34.3330       
# span 5 =     11.313,     11.535       
# span 6 =     11.400,     11.624       
# span 7 =    24.5885,    24.6098       
# span 8 =   5.142880,   5.177528       
# span 9 =    34.0931,    34.3329       
# span 10 = 1.0000e-12, 1.0000e-12      
# span 11 =     0.1492,     0.1571      
# span 12 =      98.75,      98.75      
# span 13 =    189.686,    210.464      
# span 14 =     4.3449,     4.8208      
# span 15 = 1.9107e+00, 2.1036e+00      
# span 16 =          1,          1      
# span 17 =        128,       1398      
# span 18 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = Jul 31 2016 15:32:30 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4303</SerialNumber>
#       <CalibrationDate>20-Jan-16</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.38501054e-003</G>
#       <H>6.47529902e-004</H>
#       <I>2.19462935e-005</I>
#       <J>1.64955605e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>3009</SerialNumber>
#       <CalibrationDate>20-Jan-16</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.04864981e+001</G>
#         <H>1.48778269e+000</H>
#         <I>3.67673536e-004</I>
#         <J>5.06417242e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>0749</SerialNumber>
#       <CalibrationDate>08-Apr-14</CalibrationDate>
#       <C1>-4.970438e+004</C1>
#       <C2>-4.005750e-001</C2>
#       <C3>1.365700e-002</C3>
#       <D1>3.669600e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.027760e+001</T1>
#       <T2>-4.522040e-004</T2>
#       <T3>4.002070e-006</T3>
#       <T4>1.971140e-009</T4>
#       <Slope>0.99992397</Slope>
#       <Offset>-1.86008</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.283700e-002</AD590M>
#       <AD590B>-8.706643e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4360</SerialNumber>
#       <CalibrationDate>20-Jan-16</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.36265052e-003</G>
#       <H>6.49800036e-004</H>
#       <I>2.30621342e-005</I>
#       <J>1.84888934e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2707</SerialNumber>
#       <CalibrationDate>20-Jan-16</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.07265688e+001</G>
#         <H>1.55946953e+000</H>
#         <I>-1.31572164e-003</I>
#         <J>1.86775491e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, User Polynomial -->
#     <UserPolynomialSensor SensorID="61" >
#       <SerialNumber>201</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <SensorName>UVP5</SensorName>
#       <A0>2.90000000</A0>
#       <A1>200.00000000</A1>
#       <A2>0.00000000</A2>
#       <A3>0.00000000</A3>
#     </UserPolynomialSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4550</SerialNumber>
#       <CalibrationDate>05/14/14</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>2500000000.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.60264283</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Transmissometer, WET Labs C-Star -->
#     <WET_LabsCStar SensorID="71" >
#       <SerialNumber>CST-1117</SerialNumber>
#       <CalibrationDate>2015-May-20</CalibrationDate>
#       <M>21.2354</M>
#       <B>-0.1557</B>
#       <PathLength>0.250</PathLength>
#     </WET_LabsCStar>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLTURT-1013</SerialNumber>
#       <CalibrationDate>2014-April-25</CalibrationDate>
#       <ScaleFactor>6.00000000e+000</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0870</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Turbidity Meter, WET Labs, ECO-NTU -->
#     <TurbidityMeter SensorID="67" >
#       <SerialNumber>FLTURT-1013</SerialNumber>
#       <CalibrationDate>2014 April 25</CalibrationDate>
#       <ScaleFactor>0.080000</ScaleFactor>
#       <!-- Dark output -->
#       <DarkVoltage>2.000000</DarkVoltage>
#     </TurbidityMeter>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>PSA916-40852</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0113</SerialNumber>
#       <CalibrationDate>06-Feb-16</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.1804e-001</Soc>
#         <offset>-0.5023</offset>
#         <A>-3.6606e-003</A>
#         <B> 1.5752e-004</B>
#         <C>-2.5279e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 0.9500</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR/Surface Irradiance -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber>16500</SerialNumber>
#       <CalibrationDate>March 28, 2013</CalibrationDate>
#       <ConversionFactor>1641.85000000</ConversionFactor>
#       <RatioMultiplier>1.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 09 2018 16:53:20, 7.23.2 [datcnv_vars = 17]
# datcnv_in = Z:\data\r2r\cruise\AT36\fileset\123657\data\at3601x.hex Z:\data\r2r\cruise\AT36\fileset\123657\data\at3601x.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Jan 09 2018 16:53:23, 7.23.2
# celltm_in = Z:\data\local\cruise\AT36\products\r2rctd\at3601x.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Jan 09 2018 16:53:26, 7.23.2
# binavg_in = Z:\data\local\cruise\AT36\products\r2rctd\at3601x.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
   39.81118  -69.58984    24.5790   5.173763    34.3287     11.535     11.624    24.5885   5.142880    34.0931 1.0000e-12     0.1492      98.75    189.686     4.3449 2.1036e+00          1       1398 0.0000e+00
   39.81118  -69.58984    24.6086   5.177421    34.3330     11.313     11.400    24.6098   5.177528    34.3329 1.0000e-12     0.1571      98.75    210.464     4.8208 1.9107e+00          1        128 0.0000e+00