* Sea-Bird SBE 9 Data File:
* FileName = C:\data\ctd\at2624998.hex
* Software Version Seasave V 7.21f
* Temperature SN = 4230
* Conductivity SN = 2148
* Number of Bytes Per Scan = 44
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Dec 02 2014 04:48:52
* NMEA Latitude = 09 04.85 N
* NMEA Longitude = 087 06.48 W
* NMEA UTC (Time) = Dec 02 2014  04:48:49
* Store Lat/Lon Data = Append to Every Scan
* System UTC = Dec 02 2014 04:48:52
# nquan = 19
# nvalues = 3                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = timeS: Time, Elapsed [seconds]
# name 3 = t090C: Temperature [ITS-90, deg C]
# name 4 = c0S/m: Conductivity [S/m]
# name 5 = sal00: Salinity, Practical [PSU]
# name 6 = depSM: Depth [salt water, m]
# name 7 = prDM: Pressure, Digiquartz [db]
# name 8 = t190C: Temperature, 2 [ITS-90, deg C]
# name 9 = c1S/m: Conductivity, 2 [S/m]
# name 10 = sal11: Salinity, Practical, 2 [PSU]
# name 11 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 12 = altM: Altimeter [m]
# name 13 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 14 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 15 = spar: SPAR/Surface Irradiance
# name 16 = pumps: Pump Status
# name 17 = nbin: number of scans per bin
# name 18 = flag: flag
# span 0 =    9.08086,    9.08086       
# span 1 =  -87.10804,  -87.10804       
# span 2 =      0.396,      7.354       
# span 3 =    24.2703,    24.7428       
# span 4 =   5.081263,   5.106885       
# span 5 =    33.7098,    33.8843       
# span 6 =     13.004,     13.463       
# span 7 =     13.078,     13.539       
# span 8 =    24.5034,    24.6765       
# span 9 =   5.094766,   5.104988       
# span 10 =    33.7468,    33.8040      
# span 11 =     0.3381,     0.3589      
# span 12 =      82.35,      98.75      
# span 13 =    155.001,    160.225      
# span 14 =     3.5490,     3.6691      
# span 15 = 2.6486e-03, 2.7473e-03      
# span 16 =          1,          1      
# span 17 =          8,        260      
# span 18 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = Dec 02 2014 04:48:49 [NMEA time, first data scan]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4230</SerialNumber>
#       <CalibrationDate>13-Feb-14</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.37250714e-003</G>
#       <H>6.48398804e-004</H>
#       <I>2.27867807e-005</I>
#       <J>1.82932302e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2148</SerialNumber>
#       <CalibrationDate>13-Feb-14</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.02241717e+001</G>
#         <H>1.52041184e+000</H>
#         <I>-2.32820915e-003</I>
#         <J>2.62534981e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>58939-0383</SerialNumber>
#       <CalibrationDate>28-Dec-10</CalibrationDate>
#       <C1>-4.928049e+004</C1>
#       <C2>-5.591409e-001</C2>
#       <C3>1.510530e-002</C3>
#       <D1>3.944700e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.017493e+001</T1>
#       <T2>-4.671701e-004</T2>
#       <T3>3.967900e-006</T3>
#       <T4>3.098920e-009</T4>
#       <Slope>0.99998000</Slope>
#       <Offset>2.55200</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.135000e-002</AD590M>
#       <AD590B>-8.132450e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2774</SerialNumber>
#       <CalibrationDate>27-Feb-14</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.32548581e-003</G>
#       <H>6.46828338e-004</H>
#       <I>2.40877633e-005</I>
#       <J>2.46309398e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2186</SerialNumber>
#       <CalibrationDate>13-Feb-14</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.02584283e+001</G>
#         <H>1.36507257e+000</H>
#         <I>-1.96436951e-003</I>
#         <J>1.90369122e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Free -->
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLNTURTD-149</SerialNumber>
#       <CalibrationDate>6-May-2010</CalibrationDate>
#       <ScaleFactor>1.54000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0600</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, User Polynomial -->
#     <UserPolynomialSensor SensorID="61" >
#       <SerialNumber>FLNTURTD-149</SerialNumber>
#       <CalibrationDate>1-Nov-2004</CalibrationDate>
#       <SensorName>Turbidity</SensorName>
#       <A0>-0.74000000</A0>
#       <A1>5.00000000</A1>
#       <A2>0.00000000</A2>
#       <A3>0.00000000</A3>
#     </UserPolynomialSensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>383</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0113</SerialNumber>
#       <CalibrationDate>14-Mar-14</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>3.6839e-001</Soc>
#         <offset>-0.5862</offset>
#         <A>-3.5001e-003</A>
#         <B> 1.9125e-004</B>
#         <C>-2.6354e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.4000</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Free -->
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Transmissometer, WET Labs C-Star -->
#     <WET_LabsCStar SensorID="71" >
#       <SerialNumber>CST854DR</SerialNumber>
#       <CalibrationDate>11-Jan-10</CalibrationDate>
#       <M>20.3874</M>
#       <B>-1.1825</B>
#       <PathLength>0.250</PathLength>
#     </WET_LabsCStar>
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR/Surface Irradiance -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber>not one</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ConversionFactor>1.00000000</ConversionFactor>
#       <RatioMultiplier>1.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 11 2018 17:53:31, 7.23.2 [datcnv_vars = 17]
# datcnv_in = Z:\data\r2r\cruise\AT26-24\fileset\115079\data\at2624998.hex Z:\data\r2r\cruise\AT26-24\fileset\115079\data\at2624998.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Jan 11 2018 17:53:32, 7.23.2
# celltm_in = Z:\data\local\cruise\AT26-24\products\r2rctd\at2624998.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Jan 11 2018 17:53:35, 7.23.2
# binavg_in = Z:\data\local\cruise\AT26-24\products\r2rctd\at2624998.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
    9.08086  -87.10804      0.396    24.7428   5.106885    33.7098     13.277     13.352    24.6765   5.104988    33.7468     0.3527      98.21    159.731     3.6569 2.6862e-03          1         20 0.0000e+00
    9.08086  -87.10804      1.297    24.2703   5.081263    33.8843     13.463     13.539    24.5034   5.094766    33.8040     0.3381      98.75    160.225     3.6691 2.7473e-03          1          8 0.0000e+00
    9.08086  -87.10804      7.354    24.5275   5.094657    33.7807     13.004     13.078    24.5821   5.098260    33.7661     0.3589      82.35    155.001     3.5490 2.6486e-03          1        260 0.0000e+00