* Sea-Bird SBE 9 Data File:
* FileName = C:\data\ctd\at1802019.hex
* Software Version Seasave V 7.20f
* Temperature SN = 4195
* Conductivity SN = 2670
* Number of Bytes Per Scan = 37
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Nov 26 2010 21:56:40
* NMEA Latitude = 27 22.01 N
* NMEA Longitude = 090 34.02 W
* NMEA UTC (Time) = Nov 26 2010 21:58:32
* Store Lat/Lon Data = Append to Every Scan
# nquan = 19
# nvalues = 4                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = t090C: Temperature [ITS-90, deg C]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = sal00: Salinity, Practical [PSU]
# name 5 = depSM: Depth [salt water, m]
# name 6 = prDM: Pressure, Digiquartz [db]
# name 7 = t190C: Temperature, 2 [ITS-90, deg C]
# name 8 = c1S/m: Conductivity, 2 [S/m]
# name 9 = sal11: Salinity, Practical, 2 [PSU]
# name 10 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 11 = altM: Altimeter [m]
# name 12 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 13 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 14 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 15 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 16 = pumps: Pump Status
# name 17 = nbin: number of scans per bin
# name 18 = flag: flag
# span 0 =   27.36698,   27.36698       
# span 1 =  -90.56710,  -90.56709       
# span 2 =    24.8283,    24.8292       
# span 3 =   5.426425,   5.427110       
# span 4 =    36.0186,    36.0226       
# span 5 =     16.104,     18.477       
# span 6 =     16.212,     18.600       
# span 7 =    24.8274,    24.8284       
# span 8 =   5.424366,   5.425089       
# span 9 =    36.0040,    36.0080       
# span 10 =     0.0685,     0.0794      
# span 11 =      98.75,      98.75      
# span 12 =    189.206,    190.309      
# span 13 =     4.3390,     4.3643      
# span 14 =     0.1467,     0.1495      
# span 15 =    96.3303,    96.3981      
# span 16 =          1,          1      
# span 17 =         16,        113      
# span 18 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = Nov 26 2010 21:58:32 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4195</SerialNumber>
#       <CalibrationDate>23-Jan-10 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.37127659e-003</G>
#       <H>6.44072063e-004</H>
#       <I>2.25168439e-005</I>
#       <J>1.88097395e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2670</SerialNumber>
#       <CalibrationDate>12-Jan-10 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.04351874e+001</G>
#         <H>1.39740257e+000</H>
#         <I>-7.99997539e-004</I>
#         <J>1.28162576e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>63505 SBE090462</SerialNumber>
#       <CalibrationDate>12/23/2002</CalibrationDate>
#       <C1>-4.872453e+004</C1>
#       <C2>2.143123e-002</C2>
#       <C3>1.347220e-002</C3>
#       <D1>3.959500e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>2.994567e+001</T1>
#       <T2>-2.488396e-004</T2>
#       <T3>3.985300e-006</T3>
#       <T4>7.998620e-010</T4>
#       <Slope>0.99992000</Slope>
#       <Offset>-1.29630</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.282050e-002</AD590M>
#       <AD590B>-9.111539e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4481</SerialNumber>
#       <CalibrationDate>12-Jan-10 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.33492523e-003</G>
#       <H>6.37136216e-004</H>
#       <I>2.07661802e-005</I>
#       <J>1.71173431e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2880</SerialNumber>
#       <CalibrationDate>12-Jan-10 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.06602669e+001</G>
#         <H>1.44142660e+000</H>
#         <I>2.34005419e-004</I>
#         <J>5.73830122e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLNTURTD-FL-1012</SerialNumber>
#       <CalibrationDate>2008-04-18</CalibrationDate>
#       <ScaleFactor>6.00000000e+000</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0820</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Turbidity Meter, WET Labs, ECO-NTU -->
#     <TurbidityMeter SensorID="67" >
#       <SerialNumber>FLNTURTD-1012</SerialNumber>
#       <CalibrationDate>2008-04-18</CalibrationDate>
#       <ScaleFactor>2.000000</ScaleFactor>
#       <!-- Dark output -->
#       <DarkVoltage>0.073000</DarkVoltage>
#     </TurbidityMeter>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Fluorometer, WET Labs ECO CDOM -->
#     <FluoroWetlabCDOM_Sensor SensorID="19" >
#       <SerialNumber>FLCDRTD-1379</SerialNumber>
#       <CalibrationDate>4/14/2010</CalibrationDate>
#       <ScaleFactor>23.000</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.081</Vblank>
#     </FluoroWetlabCDOM_Sensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Fluorometer, Turner SCUFA -->
#     <FluoroTurnerSCUFA_Sensor SensorID="17" >
#       <SerialNumber>201011</SerialNumber>
#       <CalibrationDate>2010-Aug-18</CalibrationDate>
#       <B>0.00000000e+000</B>
#       <MX>1.00000000e+000</MX>
#       <MY>0.00000000e+000</MY>
#       <Units>1</Units>
#       <ScaleFactor>3.00000000e+000</ScaleFactor>
#       <Offset>-8.10000000e-001</Offset>
#     </FluoroTurnerSCUFA_Sensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>PSA916-1162</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0723</SerialNumber>
#       <CalibrationDate>12-Feb-10p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.0720e-001</Soc>
#         <offset>-0.5097</offset>
#         <A>-1.4933e-003</A>
#         <B> 5.4177e-005</B>
#         <C>-1.3859e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92630e-004</D1>
#         <D2>-4.64800e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.0200</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-1118DR</SerialNumber>
#       <CalibrationDate>2008-04-30</CalibrationDate>
#       <M>21.4270</M>
#       <B>-1.3070</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Fluorometer, Chelsea UV Aquatracka -->
#     <FluoroChelseaUV_AquaSensor SensorID="7" >
#       <SerialNumber>107733001</SerialNumber>
#       <CalibrationDate>2010-8-18</CalibrationDate>
#       <A>0.001000</A>
#       <B>0.000000</B>
#     </FluoroChelseaUV_AquaSensor>
#   </sensor>
# </Sensors>
# datcnv_date = Feb 10 2018 22:43:08, 7.23.2 [datcnv_vars = 17]
# datcnv_in = Z:\data\r2r\cruise\AT18-02\fileset\102224\data\at1802019.hex Z:\data\r2r\cruise\AT18-02\fileset\102224\data\at1802019.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Feb 10 2018 22:43:09, 7.23.2
# celltm_in = Z:\data\local\cruise\AT18-02\products\r2rctd\at1802019.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Feb 10 2018 22:43:11, 7.23.2
# binavg_in = Z:\data\local\cruise\AT18-02\products\r2rctd\at1802019.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
   27.36698  -90.56709    24.8283   5.426801    36.0217     16.104     16.212    24.8276   5.424725    36.0067     0.0753      98.75    189.461     4.3448     0.1474    96.3828          1         43 0.0000e+00
   27.36698  -90.56710    24.8283   5.426425    36.0186     16.879     16.992    24.8274   5.424366    36.0040     0.0739      98.75    189.956     4.3561     0.1495    96.3303          1         36 0.0000e+00
   27.36698  -90.56710    24.8292   5.427110    36.0226     18.125     18.246    24.8282   5.424891    36.0068     0.0685      98.75    189.206     4.3390     0.1476    96.3767          1        113 0.0000e+00
   27.36698  -90.56710    24.8289   5.426984    36.0217     18.477     18.600    24.8284   5.425089    36.0080     0.0794      98.75    190.309     4.3643     0.1467    96.3981          1         16 0.0000e+00