* Sea-Bird SBE 9 Data File:
* FileName = C:\CTD\SP1315\wettest01.hex
* Software Version Seasave V 7.22.5
* Temperature SN = 4308
* Conductivity SN = 2766
* Number of Bytes Per Scan = 44
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 1
* Append System Time to Every Scan
* System UpLoad Time = Dec 03 2013 00:23:15
* NMEA Latitude = 32 42.45 N
* NMEA Longitude = 117 14.20 W
* NMEA UTC (Time) = Dec 03 2013  00:35:56
* Store Lat/Lon Data = Append to Every Scan
** Ship: R/V R. G. Sproul
** Cruise: SP1313 Levin
**  Station & Cast
** Position: Lat & Long
* System UTC = Dec 03 2013 00:23:15
# nquan = 20
# nvalues = 2                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = t090C: Temperature [ITS-90, deg C]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = sal00: Salinity, Practical [PSU]
# name 5 = depSM: Depth [salt water, m]
# name 6 = prDM: Pressure, Digiquartz [db]
# name 7 = t190C: Temperature, 2 [ITS-90, deg C]
# name 8 = c1S/m: Conductivity, 2 [S/m]
# name 9 = sal11: Salinity, Practical, 2 [PSU]
# name 10 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 11 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 12 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 13 = altM: Altimeter [m]
# name 14 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 15 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 16 = spar: SPAR/Surface Irradiance
# name 17 = pumps: Pump Status
# name 18 = nbin: number of scans per bin
# name 19 = flag: flag
# span 0 =   32.70762,   32.70762       
# span 1 = -117.23672, -117.23672       
# span 2 =    16.7878,    16.7923       
# span 3 =   4.296787,   4.313171       
# span 4 =    33.4924,    33.6391       
# span 5 =      2.407,      2.611       
# span 6 =      2.424,      2.629       
# span 7 =    16.7710,    16.7811       
# span 8 =   4.310063,   4.311000       
# span 9 =    33.6256,    33.6259       
# span 10 =     1.5119,     1.5355      
# span 11 =     1.8156,     1.8262      
# span 12 =    63.3489,    63.5157      
# span 13 =       4.11,       5.66      
# span 14 =    136.598,    184.602      
# span 15 =     3.1333,     4.2349      
# span 16 = 0.0000e+00, 0.0000e+00      
# span 17 =          1,          1      
# span 18 =        550,       4207      
# span 19 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = Dec 03 2013 00:23:15 [System UTC, first data scan.]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>4308</SerialNumber>
#       <CalibrationDate>06-Nov-2013 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>4.36389025e-003</A>
#       <B>6.45027612e-004</B>
#       <C>2.24556507e-005</C>
#       <D>1.84170203e-006</D>
#       <F0_Old>1000.000</F0_Old>
#       <G>4.36368990e-003</G>
#       <H>6.44815367e-004</H>
#       <I>2.24230097e-005</I>
#       <J>1.84018715e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2766</SerialNumber>
#       <CalibrationDate>27-Jun-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-9.67464979e+000</G>
#         <H>1.35836816e+000</H>
#         <I>-7.65310730e-004</I>
#         <J>1.24090386e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>0830</SerialNumber>
#       <CalibrationDate>07-NOV-2013</CalibrationDate>
#       <C1>-4.072105e+004</C1>
#       <C2>-5.540888e-001</C2>
#       <C3>3.236946e-003</C3>
#       <D1>3.098822e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.008938e+001</T1>
#       <T2>-5.534726e-004</T2>
#       <T3>3.709937e-006</T3>
#       <T4>1.015463e-008</T4>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.290360e-002</AD590M>
#       <AD590B>-8.201883e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2380</SerialNumber>
#       <CalibrationDate>06-Nov-2013 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>4.34142312e-003</A>
#       <B>6.42419348e-004</B>
#       <C>2.40659866e-005</C>
#       <D>2.30693750e-006</D>
#       <F0_Old>1000.000</F0_Old>
#       <G>4.34123028e-003</G>
#       <H>6.42210147e-004</H>
#       <I>2.40334612e-005</I>
#       <J>2.30534535e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2115</SerialNumber>
#       <CalibrationDate>23-May-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-9.89536470e+000</G>
#         <H>1.43228346e+000</H>
#         <I>-2.37828076e-003</I>
#         <J>2.45239491e-004</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLRTD-1156</SerialNumber>
#       <CalibrationDate>8-25-08</CalibrationDate>
#       <ScaleFactor>1.10000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0360</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-1119DR</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <M>20.0000</M>
#       <B>0.0000</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Free -->
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1055</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Free -->
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0255</SerialNumber>
#       <CalibrationDate>26-Jun-13</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.8630e-001</Soc>
#         <offset>-0.5087</offset>
#         <A>-2.9858e-003</A>
#         <B> 1.7224e-004</B>
#         <C>-3.1515e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.1500</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Free -->
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR/Surface Irradiance -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber></SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ConversionFactor>0.00000000</ConversionFactor>
#       <RatioMultiplier>0.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 24 2018 22:38:55, 7.23.2 [datcnv_vars = 18]
# datcnv_in = Z:\data\r2r\cruise\SP1316\fileset\124410\data\wettest01.hex Z:\data\r2r\cruise\SP1316\fileset\124410\data\wettest01.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Jan 24 2018 22:38:56, 7.23.2
# celltm_in = Z:\data\local\cruise\SP1316\products\r2rctd\wettest01.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Jan 24 2018 22:38:56, 7.23.2
# binavg_in = Z:\data\local\cruise\SP1316\products\r2rctd\wettest01.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
   32.70762 -117.23672    16.7878   4.313171    33.6391      2.611      2.629    16.7710   4.310063    33.6259     1.5355     1.8156    63.5157       4.11    184.602     4.2349 0.0000e+00          1        550 0.0000e+00
   32.70762 -117.23672    16.7923   4.296787    33.4924      2.407      2.424    16.7811   4.311000    33.6256     1.5119     1.8262    63.3489       5.66    136.598     3.1333 0.0000e+00          1       4207 0.0000e+00