* Sea-Bird SBE 9 Data File:
* FileName = C:\Data\TN281\DeckTest24052012.hex
* Software Version Seasave V 7.21b
* Temperature SN = 2195
* Conductivity SN = 2881
* Number of Bytes Per Scan = 41
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* Append System Time to Every Scan
* System UpLoad Time = May 24 2012 22:49:49
* NMEA Latitude = 48 12.33 N
* NMEA Longitude = 122 56.57 W
* NMEA UTC (Time) = May 24 2012 22:49:47
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.1g
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
* System UTC = May 24 2012 22:49:49
# nquan = 16
# nvalues = 0                           
# units = specified
# name 0 = t090C: Temperature [ITS-90, deg C]
# name 1 = c0S/m: Conductivity [S/m]
# name 2 = sal00: Salinity, Practical [PSU]
# name 3 = depSM: Depth [salt water, m]
# name 4 = prDM: Pressure, Digiquartz [db]
# name 5 = t190C: Temperature, 2 [ITS-90, deg C]
# name 6 = c1S/m: Conductivity, 2 [S/m]
# name 7 = sal11: Salinity, Practical, 2 [PSU]
# name 8 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/Kg]
# name 9 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 10 = altM: Altimeter [m]
# name 11 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 12 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 13 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 14 = nbin: number of scans per bin
# name 15 = flag: flag
# span 0 =     0.0000,     0.0000       
# span 1 =   0.000000,   0.000000       
# span 2 =     0.0000,     0.0000       
# span 3 =      0.000,      0.000       
# span 4 =      0.000,      0.000       
# span 5 =     0.0000,     0.0000       
# span 6 =   0.000000,   0.000000       
# span 7 =     0.0000,     0.0000       
# span 8 =      0.000,      0.000       
# span 9 =    0.00000,    0.00000       
# span 10 =       0.00,       0.00      
# span 11 =     0.0000,     0.0000      
# span 12 =     0.0000,     0.0000      
# span 13 =     0.0000,     0.0000      
# span 14 =          0,          0      
# span 15 = 0.0000e+00, 0.0000e+00      
# interval = meters: 2                  
# start_time = May 24 2012 22:49:49 [System UTC, first data scan.]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2195</SerialNumber>
#       <CalibrationDate>23-Feb-12</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.34901434e-003</G>
#       <H>6.51224577e-004</H>
#       <I>2.39780771e-005</I>
#       <J>2.22858686e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>2881</SerialNumber>
#       <CalibrationDate>12-Oct-11</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.03710663e+001</G>
#         <H>1.42479088e+000</H>
#         <I>1.06729270e-003</I>
#         <J>6.08592340e-006</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>0057</SerialNumber>
#       <CalibrationDate>22-Feb-12</CalibrationDate>
#       <C1>-2.869955e+004</C1>
#       <C2>-1.565582e+000</C2>
#       <C3>9.161829e-003</C3>
#       <D1>3.074801e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.023683e+001</T1>
#       <T2>-1.016075e-003</T2>
#       <T3>4.744095e-006</T3>
#       <T4>0.000000e+000</T4>
#       <Slope>0.99980000</Slope>
#       <Offset>-8.55800</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.133000e-002</AD590M>
#       <AD590B>-8.498580e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2060</SerialNumber>
#       <CalibrationDate>23-Feb-12</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.13897250e-003</G>
#       <H>6.25024768e-004</H>
#       <I>2.05347545e-005</I>
#       <J>2.08075011e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1824</SerialNumber>
#       <CalibrationDate>30-Nov-11</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.15188213e+000</G>
#         <H>5.57831770e-001</H>
#         <I>-7.57079565e-004</I>
#         <J>6.96537524e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0518</SerialNumber>
#       <CalibrationDate>13-Dec-11</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.9360e-001</Soc>
#         <offset>-0.5268</offset>
#         <A>-3.0579e-003</A>
#         <B> 1.0450e-004</B>
#         <C>-1.7256e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 2.0100</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>49777</SerialNumber>
#       <CalibrationDate>3/1/2012</CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Free -->
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Free -->
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Oxygen, SBE 43, 2 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0023</SerialNumber>
#       <CalibrationDate>10-Feb-12</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.3418e-001</Soc>
#         <offset>-0.5182</offset>
#         <A>-2.5112e-003</A>
#         <B> 1.4798e-004</B>
#         <C>-2.6123e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.1700</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4747</SerialNumber>
#       <CalibrationDate>05Apr2011</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>10741138560.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.13267700</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLRTD-063</SerialNumber>
#       <CalibrationDate>April-20-2011</CalibrationDate>
#       <ScaleFactor>1.30000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0460</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-1313DR</SerialNumber>
#       <CalibrationDate>18-Nov-2011</CalibrationDate>
#       <M>21.3678</M>
#       <B>-1.1742</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 29 2014 20:30:32, 7.21d [datcnv_vars = 14]
# datcnv_in = U:\temp\data\TN281_105241_ctd\decktest24052012.hex U:\temp\data\TN281_105241_ctd\decktest24052012.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# binavg_date = Jan 29 2014 20:30:32, 7.21d
# binavg_in = T:\processed\TN281_105241_ctd\decktest24052012.cnv
# binavg_bintype = meters
# binavg_binsize = 2
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*