* Sea-Bird SBE 9 Data File:
* FileName = C:\Data\TN270\TN270_Cast_6.hex
* Software Version Seasave V 7.21b
* Temperature SN = 1316
* Conductivity SN = 1084
* Number of Bytes Per Scan = 41
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* Append System Time to Every Scan
* System UpLoad Time = Oct 09 2011 00:26:58
* NMEA Latitude = 47 27.35 N
* NMEA Longitude = 122 24.51 W
* NMEA UTC (Time) = Oct 09 2011 00:26:56
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.1g
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
* System UTC = Oct 09 2011 00:26:58
# nquan = 16
# nvalues = 3                           
# units = specified
# name 0 = t090C: Temperature [ITS-90, deg C]
# name 1 = c0S/m: Conductivity [S/m]
# name 2 = sal00: Salinity, Practical [PSU]
# name 3 = depSM: Depth [salt water, m]
# name 4 = prDM: Pressure, Digiquartz [db]
# name 5 = t190C: Temperature, 2 [ITS-90, deg C]
# name 6 = c1S/m: Conductivity, 2 [S/m]
# name 7 = sal11: Salinity, Practical, 2 [PSU]
# name 8 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/Kg]
# name 9 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 10 = altM: Altimeter [m]
# name 11 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 12 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 13 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 14 = nbin: number of scans per bin
# name 15 = flag: flag
# span 0 =    11.9914,    12.1531       
# span 1 =   3.477532,   3.480764       
# span 2 =    29.8288,    29.9874       
# span 3 =      4.000,      8.000       
# span 4 =      4.034,      8.067       
# span 5 =    11.9926,    12.1621       
# span 6 =   3.477253,   3.480629       
# span 7 =    29.8190,    29.9852       
# span 8 =    173.187,    193.370       
# span 9 =    3.96593,    4.42745       
# span 10 =      98.51,      98.51      
# span 11 =     1.8137,     4.2863      
# span 12 =     0.1564,     0.2221      
# span 13 =    94.6007,    96.1662      
# span 14 =        238,       2149      
# span 15 = 0.0000e+00, 0.0000e+00      
# interval = meters: 2                  
# start_time = Oct 09 2011 00:26:58 [System UTC, first data scan.]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>1316</SerialNumber>
#       <CalibrationDate>12-Feb-11</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.87156145e-003</G>
#       <H>6.80810154e-004</H>
#       <I>2.76799824e-005</I>
#       <J>2.23173938e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1084</SerialNumber>
#       <CalibrationDate>16-Feb-11</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.18838799e+000</G>
#         <H>4.75567581e-001</H>
#         <I>-3.04708907e-004</I>
#         <J>3.88840524e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>94112-0216</SerialNumber>
#       <CalibrationDate>07-may-2008</CalibrationDate>
#       <C1>-4.562074e+004</C1>
#       <C2>1.820199e-001</C2>
#       <C3>1.580430e-002</C3>
#       <D1>3.615300e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.024088e+001</T1>
#       <T2>-3.472576e-004</T2>
#       <T3>4.427560e-006</T3>
#       <T4>3.763240e-009</T4>
#       <Slope>0.99992000</Slope>
#       <Offset>-2.70470</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.176000e-002</AD590M>
#       <AD590B>-8.544400e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>1605</SerialNumber>
#       <CalibrationDate>12-Feb-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.84496866e-003</G>
#       <H>6.76788005e-004</H>
#       <I>2.51666158e-005</I>
#       <J>1.86679798e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1698</SerialNumber>
#       <CalibrationDate>16-Feb-11 </CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.34204187e+000</G>
#         <H>5.22253404e-001</H>
#         <I>-5.80951291e-004</I>
#         <J>5.41987630e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0518</SerialNumber>
#       <CalibrationDate>29-Sep-10p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.9660e-001</Soc>
#         <offset>-0.5244</offset>
#         <A>-3.1298e-003</A>
#         <B> 1.6682e-004</B>
#         <C>-3.4409e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.3300</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1098</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Oxygen, SBE 43, 2 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0542</SerialNumber>
#       <CalibrationDate>09-Feb-11p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.6080e-001</Soc>
#         <offset>-0.4860</offset>
#         <A>-2.3554e-003</A>
#         <B> 1.4402e-004</B>
#         <C>-2.4999e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.3800</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Free -->
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4747</SerialNumber>
#       <CalibrationDate>April-05-2011</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>1418439716.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-1.04000000</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Free -->
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>FLRTD-063</SerialNumber>
#       <CalibrationDate>April-20-2011</CalibrationDate>
#       <ScaleFactor>2.50000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0260</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-402DR</SerialNumber>
#       <CalibrationDate>March-11-2011</CalibrationDate>
#       <M>21.4904</M>
#       <B>-1.2071</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
# </Sensors>
# datcnv_date = Jan 29 2014 00:56:24, 7.21d [datcnv_vars = 14]
# datcnv_in = U:\temp\data\TN270_103698_ctd\tn270_cast_6.hex U:\temp\data\TN270_103698_ctd\tn270_cast_6.XMLCON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# binavg_date = Jan 29 2014 00:56:25, 7.21d
# binavg_in = \\Misc\NSF-R2R\processed\TN270_103698_ctd\tn270_cast_6.cnv
# binavg_bintype = meters
# binavg_binsize = 2
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
    11.9914   3.480764    29.9874      8.000      8.067    11.9926   3.480629    29.9852    173.187    3.96593      98.51     1.8137     0.1564    96.1662       2149 0.0000e+00
    12.0526   3.479570    29.9278      6.000      6.051    12.0611   3.479333    29.9188    176.208    4.03487      98.51     2.7363     0.1916    95.3244        238 0.0000e+00
    12.1531   3.477532    29.8288      4.000      4.034    12.1621   3.477253    29.8190    193.370    4.42745      98.51     4.2863     0.2221    94.6007        479 0.0000e+00