* Sea-Bird SBE 9 Data File:
* FileName = D:\CTDData\WaterTests\test7.hex
* Software Version Seasave V 7.20c
* Temperature SN = 2899
* Conductivity SN = 1446
* Number of Bytes Per Scan = 40
* Number of Voltage Words = 5
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = May 31 2010 21:13:12
* NMEA Latitude = 42 17.91 N
* NMEA Longitude = 070 30.00 W
* NMEA UTC (Time) = May 31 2010  21:13:10
* Store Lat/Lon Data = Append to Every Scan
** Vessel: RV Endeavor
** Cruise: EN476
** Chief Scientist: Dennis McGillicuddy
# nquan = 21
# nvalues = 2                           
# units = specified
# name 0 = latitude: Latitude [deg]
# name 1 = longitude: Longitude [deg]
# name 2 = t090C: Temperature [ITS-90, deg C]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = sal00: Salinity, Practical [PSU]
# name 5 = depSM: Depth [salt water, m]
# name 6 = prDM: Pressure, Digiquartz [db]
# name 7 = t190C: Temperature, 2 [ITS-90, deg C]
# name 8 = c1S/m: Conductivity, 2 [S/m]
# name 9 = sal11: Salinity, Practical, 2 [PSU]
# name 10 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 11 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 12 = altM: Altimeter [m]
# name 13 = par: PAR/Irradiance, Biospherical/Licor
# name 14 = sbeox0Mm/Kg: Oxygen, SBE 43 [umol/kg]
# name 15 = sbeox0ML/L: Oxygen, SBE 43 [ml/l]
# name 16 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 17 = spar: SPAR/Surface Irradiance
# name 18 = pumps: Pump Status
# name 19 = nbin: number of scans per bin
# name 20 = flag: flag
# span 0 =   42.29863,   42.29877       
# span 1 =  -70.50007,  -70.49989       
# span 2 =    13.1204,    13.4292       
# span 3 =   3.645828,   3.665141       
# span 4 =    30.5666,    30.6364       
# span 5 =      6.391,      6.541       
# span 6 =      6.442,      6.593       
# span 7 =    13.1397,    13.4971       
# span 8 =   1.041486,   1.954604       
# span 9 =    12.1263,    16.0922       
# span 10 =     0.6055,     0.6145      
# span 11 =    85.7598,    85.9518      
# span 12 =      99.98,      99.98      
# span 13 = 7.8937e+01, 8.0342e+01      
# span 14 =    246.093,    275.811      
# span 15 =     5.6365,     6.3179      
# span 16 =     0.4285,     0.5105      
# span 17 = 1.2505e+03, 1.2531e+03      
# span 18 =          0,          1      
# span 19 =        387,        607      
# span 20 = 0.0000e+00, 0.0000e+00      
# interval = decibars: 1                
# start_time = May 31 2010 21:13:10 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="15" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2899</SerialNumber>
#       <CalibrationDate>14-Apr-10</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>3.67981932e-003</A>
#       <B>6.00355007e-004</B>
#       <C>1.49491388e-005</C>
#       <D>2.02090165e-006</D>
#       <F0_Old>6082.096</F0_Old>
#       <G>4.37878440e-003</G>
#       <H>6.50381935e-004</H>
#       <I>2.32263476e-005</I>
#       <J>2.10143222e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>1446</SerialNumber>
#       <CalibrationDate>13-Apr-10</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>5.15892540e-005</A>
#         <B>4.57393029e-001</B>
#         <C>-3.99774258e+000</C>
#         <D>-8.54504249e-005</D>
#         <M>3.7</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.19067388e+000</G>
#         <H>5.55783783e-001</H>
#         <I>1.75976540e-004</I>
#         <J>1.77408479e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>80016</SerialNumber>
#       <CalibrationDate>06-Mar-09</CalibrationDate>
#       <C1>-4.589988e+004</C1>
#       <C2>-1.257540e+000</C2>
#       <C3>1.319840e-002</C3>
#       <D1>3.383500e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.008300e+001</T1>
#       <T2>-6.730880e-004</T2>
#       <T3>3.893580e-006</T3>
#       <T4>2.333810e-009</T4>
#       <Slope>1.00004000</Slope>
#       <Offset>-1.73980</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.284520e-002</AD590M>
#       <AD590B>-8.669590e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2107</SerialNumber>
#       <CalibrationDate>14-Apr-10</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.14731881e-003</G>
#       <H>6.27686897e-004</H>
#       <I>2.08621420e-005</I>
#       <J>2.11979852e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>0864</SerialNumber>
#       <CalibrationDate>13-Apr-10</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.13502391e+000</G>
#         <H>5.95406684e-001</H>
#         <I>-6.82219193e-004</I>
#         <J>6.99997404e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>399DR</SerialNumber>
#       <CalibrationDate>25-Apr-08/11-Mar-10 field</CalibrationDate>
#       <M>20.7449</M>
#       <B>-1.1845</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1075</SerialNumber>
#       <CalibrationDate>14-May-10deck</CalibrationDate>
#       <ScaleFactor>14.780</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4479</SerialNumber>
#       <CalibrationDate>08-Feb-07</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>8130100000.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.21722300</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0348</SerialNumber>
#       <CalibrationDate>10-Apr-10p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>4.3820e-001</Soc>
#         <offset>-0.4851</offset>
#         <A>-1.2560e-003</A>
#         <B> 1.3673e-004</B>
#         <C>-2.9491e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92630e-004</D1>
#         <D2>-4.64800e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.0400</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, Oxygen, SBE 43, 2 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0343</SerialNumber>
#       <CalibrationDate>28-Apr-10p</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.6950e-001</Soc>
#         <offset>-0.5301</offset>
#         <A>-3.0509e-003</A>
#         <B> 1.7133e-004</B>
#         <C>-3.4265e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92630e-004</D1>
#         <D2>-4.64800e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.4500</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Free -->
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>478</SerialNumber>
#       <CalibrationDate>27-Mar-09</CalibrationDate>
#       <ScaleFactor>2.50000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0210</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="14" >
#     <!-- SPAR voltage, Unavailable -->
#   </sensor>
#   <sensor Channel="15" >
#     <!-- SPAR voltage, SPAR/Surface Irradiance -->
#     <SPAR_Sensor SensorID="51" >
#       <SerialNumber>20121</SerialNumber>
#       <CalibrationDate>24-Feb-06</CalibrationDate>
#       <ConversionFactor>1700.17000000</ConversionFactor>
#       <RatioMultiplier>1.00000000</RatioMultiplier>
#     </SPAR_Sensor>
#   </sensor>
# </Sensors>
# datcnv_date = Feb 03 2018 17:24:50, 7.23.2 [datcnv_vars = 19]
# datcnv_in = Z:\data\r2r\cruise\EN476\fileset\107316\data\test7.hex Z:\data\r2r\cruise\EN476\fileset\107316\data\test7.CON
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = no
# datcnv_ox_tau_correction = yes
# celltm_date = Feb 03 2018 17:24:53, 7.23.2
# celltm_in = Z:\data\local\cruise\EN476\products\r2rctd\test7.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# binavg_date = Feb 03 2018 17:24:56, 7.23.2
# binavg_in = Z:\data\local\cruise\EN476\products\r2rctd\test7.cnv
# binavg_bintype = decibars
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.000, max = 0.000, value = 0.000
# file_type = ascii
*END*
   42.29863  -70.50007    13.1204   3.645828    30.6364      6.541      6.593    13.1397   1.041486    12.1263     0.6145    85.7598      99.98 8.0342e+01    275.811     6.3179     0.5105 1.2531e+03          0        607 0.0000e+00
   42.29877  -70.49989    13.4292   3.665141    30.5666      6.391      6.442    13.4971   1.954604    16.0922     0.6055    85.9518      99.98 7.8937e+01    246.093     5.6365     0.4285 1.2505e+03          1        387 0.0000e+00